How To Change The Blade On A Craftsman 10 Inch Miter Saw

Information technology does not thing which brand's miter saw you are using, the process for changing the blade is almost identical.

Miter saws are used in wooden works all over the world. However, it tin can also cut some metals like steel and aluminum.

The i reason for the replacement of the miter saw blade is rusting of the blade. Another reason might exist less sharpness or dullness of the blade.

If anyone of the above situations occurs, information technology would lessen the efficiency of your miter saw. Therefore, you lot need to replace your blade. This keeps the work consistent.

Appliance Required For The Replacement Of Blade

To perform the replacement of Craftsman miter saw blade, you should take these things bachelor with y'all:

Screwdriver
iii/8 inch wrench
Machine oil
Safety equipment

Steps To Follow How To Change Bract On Craftsman Miter Saw

If your miter saw is non cutting the materials properly, you must change your blade for ameliorate performance.

Also, if the demand arises, y'all tin can alter both the blade guard on the craftsman miter saw and blade craftsman table saw.

But hither we will but teach you how you tin change your blade on a craftsman miter saw. It requires a few stepwise process to be followed:

Stride-one: Take Good Safety Precautions

For changing the blade on a craftsman miter saw, the first pace is to have some skilful security precautions.

Dealing with the blade is always risky, so you should wear a mask and a pair of gloves earlier starting the replacement procedure.

However, it is necessary to unplug whatsoever power tool before you commencement its maintenance. If the bract of the craftsman miter saw is spinning, expect for it to stop before you kickoff working with it.

Stride-two: Loose The Blade Arm

If the blade arm of the miter saw is locked and in its working position which is down, heighten the bract arm to its total height by unlocking it. This volition assist in exposing the blade to you.

Footstep-3: Detach The Guard

To remove the blade, nosotros should beginning remove the blade guard so that information technology does not hinder the replacement of the blade.

Step-four: Remove The Blade Bolt

For removing the blade, first, you demand to remove the bract bolt. So, remove the bolt comprehend offset by moving information technology upward and so, loosen the bract bolt with a 3/8 inch wrench subsequently locking the spindle of the blade arm.

In case, the spindle of the miter saw is not locked properly, you will be unable to remove the blade commodities due to its frequent rotation.

Footstep-five: Remove The Bract

Once yous have removed the bract bolt, now, remove the outer washer of the bract and keep the inner washer at its place.

While putting the new blade, brand certain to place the outer washer again at its place otherwise, it tin can cause an blow.

For doing this, make sure the spindle of your craftsman miter saw is fully locked then that the blade cannot rotate.

Remove the blade and give oil to the indicate where the inner washer and outer washer contacts with the blade.

Footstep-6: Prepare New Bract

Now, yous are all set to fix the new blade in the miter saw. After putting the new blade, put the outer washer at its place and starting time tightening the blade commodities of the craftsman miter saw with a three/viii inch wrench.

Make sure your blade has been fully tightened to avert any accidental situation. Loose blade bolts can be dangerous.

Pace-7: Reattach The Bract Guard

Now, put the bolt blade comprehend on the blade arm and reattach the bract guard on the craftsman miter saw.

Brand sure to unlock the spindle before plugging in the craftsman miter saw.

Congratulations! You lot have replaced your craftsman miter saw blade successfully.

FAQs

How to Modify The Blade On A Craftsman x-inch Miter Saw?

Here we will tell you how to replace the bract on a craftsman ten-inch miter saw. The procedure is as follows:

First of all, take proficient safety measures and too unplug the miter saw earlier you start working.
And then, remove the guard and start losing the bract commodities.
Offset, remove the outer washer and then carefully remove the blade of the craftsman miter saw.
Attach the new bract and the guard of the miter saw.
In the end, unlock the spindle of the miter saw.

How To Replace A Guard On A Craftsman Miter Saw?

If the guard of your craftsman miter saw does not work properly, you demand to replace it by following a simple procedure. Just you demand a wrench for this purpose. Later on having a wrench available with you, kickoff removing the commodities of the guard. After removing it, now advisedly detach the guard of your miter saw.